DELL PP39L SPECS PDF

You've been outbid by See all options. Pick-up for this item is available at our warehouse in Farmingdale, New York. Please carefully review our shipping and returns policy before committing to a bid. Shipping is only available within the US.

Author:Goltikasa Tami
Country:Burma
Language:English (Spanish)
Genre:Technology
Published (Last):23 August 2016
Pages:124
PDF File Size:15.23 Mb
ePub File Size:9.52 Mb
ISBN:231-5-77517-295-8
Downloads:63127
Price:Free* [*Free Regsitration Required]
Uploader:Nekinos



Manual zz. Information in this document is subject to change without notice. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. For additional safety best practices information, see the Regulatory Compliance Homepage at www. WARNING: Before performing these procedures, turn off the computer, disconnect the AC adapter from the electrical outlet and the computer, disconnect the modem from the wall connector and the computer, and remove any other external cables from the computer.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface such as a connector on the back of the computer. Removing the Base Cover 1. Ensure that the computer is turned off. Loosen the three captive screws on the base cover and lift the cover off the computer at an angle as shown in the figure.

Align the tabs on the base cover to the bottom of the computer. Tighten the three captive screws on the base cover. Slide the battery into the battery bay until it clicks into place. Unless otherwise noted, each procedure assumes that: l You have performed the steps in Before Working Inside Your Computer. Save and close all open files and exit all open programs. The computer turns off after the operating system shutdown process finishes. Ensure that the computer and any attached devices are turned off.

If your computer and attached devices did not automatically turn off when you shut down your operating system, press and hold the power button for at least 8 to 10 seconds until the computer turns off. Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety. Damage due to servicing that is not authorized by Dell is not covered by your warranty. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface, such as a connector on the back of the computer.

Do not touch the components or contacts on a card. Hold a card by its edges. Hold a component such as a processor by its edges, not by its pins. For cable connectors with locking tabs, press inward on the locking tabs to release the connector. Ensure that the work surface is flat and clean to prevent the computer cover from being scratched. Turn off your computer see Turning Off Your Computer. Disconnect any telephone or network cables from the computer.

Do not use batteries designed for other Dell computers. Turn the computer over. Slide the battery release latch until it clicks into place. Slide the battery out of the battery bay. Turn the computer top side up, open the display, and press the power button to ground the system board. Failure to do so may cause system damage. Ensure that the AC adapter is plugged in and that the main battery is installed properly. Otherwise, you must enter the system setup program to change the default boot order.

Doing so may cause damage to the computer. Follow the instructions that appear on the screen. The computer continues to boot and updates the new BIOS. When the flash update is complete, the computer will automatically reboot.

Failure to do so may cause damage to the computer. Ensure that the AC adapter is plugged in, the main battery is properly installed, and a network cable is attached.

Turn on the computer. Locate the latest BIOS update file for your computer at support. Click Download Now to download the file.

The File Download window appears. Click Save this program to disk, and then click OK. The Save In window appears. Click the down arrow to view the Save In menu, select Desktop, and then click Save.

The file downloads to your desktop. Click Close if the Download Complete window appears. The file icon appears on your desktop and is titled the same as the downloaded BIOS update file. Doing so may cause system damage. Double-click the file icon on the desktop and follow the instructions on the screen.

Removing the Camera Module 1. Follow the instructions in Before You Begin. Remove the display panel see Removing the Display Panel. Remove the two screws that secure the camera to the display cover. Lift the camera board from the display cover. Replace and tighten the two screws securing the camera to the display cover.

Replace the display panel see Replacing the Display Panel. Removing the Center Control Cover 1 1. Follow the procedures in Before You Begin. Remove the screw securing the center control cover from the battery bay. Turn the computer over and open the display as far as possible. Pry out the center control cover with a plastic scribe starting from the battery bay location at the back of the computer.

Ease the center control cover up. Align the hooks beneath the center control cover to the slots on the palm rest and snap the cover in place. Close the display and turn over the computer. In the battery bay, replace the screw that secures the center control cover.

Removing the Coin-Cell Battery 1. Remove the base cover see Removing the Base Cover. Use a plastic scribe to pry up the coin-cell battery from the slot.

Hold the coin-cell battery with the positive side up. Slide the coin-cell battery into the slot and gently press until it snaps to the slot. Replace the base cover see Replacing the Base Cover. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface such as the back panel on the computer. CAUTION: To prevent intermittent contact between the ZIF-socket cam screw and the processor when removing or replacing the processor, press to apply slight pressure to the center of the processor while turning the cam screw.

CAUTION: To avoid damage to the processor, hold the screwdriver so that it is perpendicular to the processor when turning the cam screw. Removing the Processor Module 1. Remove the processor heat sink see Removing the Processor Heat Sink. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop.

The oils in your skin can reduce the heat transfer capability of the thermal pads. Be careful not to bend the pins on the processor module. Lift the processor module from the ZIF socket. Replacing the Processor Module NOTE: If a new processor is installed, you will receive a new thermal-cooling assembly, which will include an affixed thermal pad, or you will receive a new thermal pad along with documentation to illustrate proper installation.

Align the pin-1 corner of the processor module with the pin-1 corner of the ZIF socket, then insert the processor module. When the processor module is properly seated, all four corners are aligned at the same height. If one or more corners of the module are higher than the others, the module is not seated properly. Tighten the ZIF socket by turning the cam screw clockwise to secure the processor module to the system board. Replace the processor heat sink see Replacing the Processor Heat Sink.

WARNING: If you remove the processor heat sink from the computer when the heat sink is hot, do not touch the metal housing of the processor heat sink. Removing the Processor Heat Sink 1. Remove the optical drive see Removing the Optical Drive. Disconnect the ExpressCard cables from the respective connectors on the system board see Removing the ExpressCard Board. Remove the six screws that secure the system board to the computer base.

Turn the system board over.

TRAUMATISMO ENCEFALOCRANEANO PDF

Dell Studio 1558

Manual zz. Information in this document is subject to change without notice. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc.

DESCARGAR LA ENZIMA PRODIGIOSA GRATIS PDF

Dell Studio 15 (1555) Review

This multimedia machine offers strong performance, long battery life, rich sound, and a comfortable keyboard at an excellent price. It's easy to find a notebook that's good at the basics. But what if you want to edit photos and video? Or multitask without your laptop wheezing? We love its comfortable keyboard, high-resolution webcam, strong performance, rich sound, and long battery life.

MICROECONOMIA PINDYCK 5 EDICION PDF

Basic Specifications - Dell Studio PP39L Setup Manual

Now with more than customizable designs available from the Dell Design Studio, is the Studio 15 the most attractive inch notebook on the market? Dell Studio 15 Specifications:. Dell decided that the original Studio 15 model needed some improvements, and when LCD manufacturers stopped making ratio LCDs and switched to ratio screens it gave Dell the perfect opportunity to launch a new Studio 15 With that being said, the changes between the original Studio 15 and the new Studio 15 are fairly minor. Dell obviously increased the width of the notebook in order to accommodate the wider The new Studio 15 also features a black screen bezel compared to the silver bezel on the old Studio

Related Articles